Browse Categories
Browse by Manufacturer
Shopping Cart
Your cart is empty.
PRL Motorsports LLC
2018+ Honda Accord 2.0T & 1.5T Intercooler Upgrade
Fits 2018+ Honda Accord 2.0T & 1.5T Models.

Starting at $599.99
Finish Options:
Click to Enlarge Image

Product Description



Fitment Notes:

2018+ HONDA ACCORD 1.5T & 2.0T

Please Read Before Ordering:


Technical Notes:

It’s no secret that Honda’s newer turbo platforms are extremely susceptible to heat-soak, especially when retaining the factory intercooler. Excessive heat-soak increases the risk of detonation and causes major power-loss due to high charge air and cylinder temperatures. These issues become even more prevalent with spirited driving and/or increased power outputs.

The PRL Motorsports intercooler upgrade decreases charge air temperatures while increasing potential airflow with its dense 27 x 3.5 x 7.25" 550+ horsepower rated bar-and-plate core. Our intercooler core which increases surface area by 85% and internal flow by 83% to allow optimal cooling and airflow.

This intercooler utilizes factory mounting spots with cast aluminum end tanks as well as all factory air ducts/shrouds. *To maintain consistency with most of our PRL product line, no cutting, fitting or trimming is required. Kits will come with all hardware needed for a seamless install.

Intercooler Core Information:


Kit Includes:
  • (1) Intercooler Assembly
  • (1) Cardboard Stencil w/ “PRL” Logo
  • (1) Buna O-Ring
  • (1) 304 Stainless Worm Clamp

Performance Gains:

  • Mid-range & top-end power gains
  • Major drop in post charge air temperature at peak
  • Increased efficiency & consistency in power delivery
  • Increased engine safety

Intercooler to Charge Pipe Bolt(s) Torque Spec:

  • 18 ft/lb

If you plan to utilize the provided stencil to represent PRL on your intercooler:
-Clean and make sure your intercooler is dry.
-Place the cardboard stencil onto the front of the intercooler (Make sure the intercooler is not upside down, the PRL logo is on the driver's side end tank).
-It is recommended to tape down the stencil to have a sharp logo and to avoid moving.
-Mask off or cover the end tanks to avoid overspray.
-Apply a high temp engine enamel style spray paint (we recommend Duplicolor DE1635 Ford SemiGloss Black, any color can be used).
-Multiple coats may be needed to have full coverage, this varies per color.
-Allow to dry 30-60 minutes before installing the intercooler.
-If any mistakes are made such as runs/overspray acetone or paint thinner can be used to remove any unwanted paint or to remove the stencil entirely, though this will take some time.

-Keep the stencil handy and in a safe spot without bending if you would like to refresh your intercooler after years of road debris blasting it! (Stop blowing holes in my ship!)

Product Reviews

(12 Ratings, 4 Reviews) Average Rating:
Just like factory
Anthony Schirripa (Bridgeville, PA) 4/3/2021 7:25 PM
I was a little worried about fitment being the size difference. When I say it fell into place I mean it, couldn’t have been an easier install. Bravo PRL
Works as expected
Dario Giomi (CA) 2/19/2020 6:37 PM
Good fit and finish. Easy to install but no instructions.
nice fit tough install
brett (md) 7/30/2019 8:45 PM
the install was not bad except for the honda sense sensor. that caused me to have to pull both headlights and use a swivel 10mm to get the four bolts. great fit. good quality. haven't ran it yet, still building, but it looks much bigger than stock.
Keeping cool!
Andy (Raleigh) 7/29/2019 9:19 PM
The intercooler install was a bit tough. There is definitely some body parts to move out of the way. What isvery impressive was how efficient the intercooler worked pull after pull after pull. 1-2-3-4 shifts. IAT2 temps would be barely 10 degrees over ambient indicating the efficiency of the intercooler.